How thick will a hypertherm 45 cut?
Cut capacity
| Capacity | Thickness | Cut speed |
|---|---|---|
| Cutting | ||
| Recommended | 16 mm (5/8″) 22 mm (7/8″) | 500 mm/min (20 ipm) 250 mm/min (10 ipm) |
| Severance (hand cutting) | 29 mm (1-1/8″) | 125 mm/min (5 ipm) |
| Pierce* | 12 mm (1/2″) |
Is hypertherm a good plasma cutter?
However, its overall value can’t be perceived through price alone – it’s a superior, powerful plasma cutter with plenty of versatility to go about, it can switch through consumables at a rapid rate, and it’s very compact and transportable. Overall, it’s more than worth the price.
How much does a Hypertherm plasma cutter cost?
Compare with similar items
| This item Hypertherm Powermax 65 G4 Plasma Cutter with Machine Torch & Remote On/Off Switch | LOTOS LTP5000D 50Amp Non-Touch Pilot Arc Plasma Cutter, Dual Voltage 110V/220V, 1/2 Inch Clean Cut, Brown | |
|---|---|---|
| Price | $3,599.00 | $399.00$399.00 |
| Sold By | Harris Welding Supplies | Amazon.com |
What is the kerf of a plasma cutter?
Kerf is the width of material (perpendicular to the torch and cut axis) removed during the plasma cutting process. Kerf is affected by three major variables. Cutting Speed. Faster cutting speeds with other variables constant will result in a narrower kerf.
What size air compressor is needed to run a plasma cutter?
All plasma manufacturers include minimum air flow and pressure requirements for an air compressor in the owner’s manual. These requirements differ between systems, but as an example, an air compressor for a plasma cutter like the Hypertherm Powermax45® requires 6 cubic feet per minute (cfm) at 90 psi.
Does hypertherm make welders?
Welders Supply is the best Hypertherm dealer in the United States (and, quite possibly, the universe). You’ll find the lowest prices on plasma cutters, hand and mechanized torches, consumables, accessories, safety gear, and thousands of other welding equipment essentials.
What’s the best plasma cutter?
The 9 Best Plasma Cutters
- Lotos LTP5000D Plasma Cutter.
- Yeswelder CUT-55DS Plasma Cutter.
- Eastwood Versa Cut 40 Amp Plasma Cutter.
- Hobart Airforce 27i Plasma Cutter.
- Lincoln Electric Plasma 20 Plasma Cutter.
- Hypertherm Powermax 45 Plasma Cutter.
- Primeweld Cut60 Plasma Cutter.
- Miller Spectrum 625 Plasma Cutter.
How does a Hypertherm plasma cutter work?
A plasma cutter or plasma cutting system uses a plasma stream to transfer energy to a conductive work material. The plasma arc cuts the workpiece by first melting it, and then blowing away the molten metal.
How do you reduce slag when cutting plasma?
Solutions:
- Replace worn cutting tip, especially if the orifice shows signs of wear.
- Decrease the speed of your cut incrementally until dross in minimized.
- Lower the torch height incrementally.
- Boost current, being careful not to exceed 95% of your nozzles AMP rating.
What is needed for plasma cutting?
Plasma cutting requires two basic elements — air and electricity — so the next question to ask is what type of input power is available. Several 30-amp plasma cutters, such as the Spectrum® 375 X-TREME™, operate using 120- or 240-volt power.
What’s the difference between Hypertherm PowerMax 45 and XP?
Hypertherm Powermax45 XP A step up from the Powermax 45, this professional-grade plasma system ups the cut capacity to 5/8” (16mm) and offers faster cut speeds.
Are there any Hypertherm plasma cutters in stock?
Hypertherm Powermax 30xp Plasma System NEW MODEL In STOCK! Hypertherm’s cutting edge line of plasma cutters cut through just about anything. Naturally, Welders Supply cuts the price to help all of our professional welding customers. A Powermax Plasma Cutter from Hypertherm is your sure path to more profits.
Why is Hypertherm using PowerMax air plasma system?
Using Powermax Systems gets work done faster, better and easier with less cost and more dependability. Hypertherm invests heavily in product engineering to keep on the cutting edge of technology. The latest technological breakthroughs are always designed into new Powermax Air Plasma Systems.
What makes the powermax45 XP plasma cutter so good?
Patented drag-cutting technology makes the Powermax45 XP easy to use – even for first-time operators A wide range of torch and consumable styles to choose from for both handheld and automated processes Plasma cutting efficiency is 11% better than its predecessor, enabling you to cut more steel with less power, in less time
