How do I reset my Jandy salt cell?
Each time a flow sensor is unplugged and plugged back in again the computer inside the unit must be reset by turning the power ‘off’ and then ‘on’.
What does check AquaPure general fault mean?
Posted July 14, 2009. The unit is reporting that your Chlorine generator has a problem and needs your attention. You will need to go out to the pool equipment and wait for the Aqua Pure to display a 3 digit code, This code will direct you to the problem.
Why does AquaPure say no flow?
I would like to remind everyone that if your AquaPure system is showing “No Flow”, with or without any other error codes, your system IS NOT making chlorine. Don’t ignore it.
What does cell reversing mean on AquaPure?
AquaPure automatically cleans the Cell electrodes once every 3 hours by reversing polarity. This does not interrupt the production of Chlorine.
How do I know if my salt cell is bad?
If the salt cell bubbles, but only a little bit, then you probably have a bad cell. It is still a good idea to call a pool professional to confirm this diagnosis. If the salt cell bubbles vigorously, then it is working fine.
How do I reset my Jandy Aquapure 1400?
Turn off the system and unplug the little board and then reinstall it. Turn on the system, wait for about 5 minutes, and then hold the little white button for 5 seconds. This will calibrate the sensor.
How do you reset the Zodiac chlorinator?
– If TRi electrode has been replaced, press the ‘Select’ switch to reset cell operating hours. – If not (just for a normal control), press the ‘Menu’ switch to come back to default LCD display. (all memories and setting are consequently reset to zero).
Why is my salt generator not producing chlorine?
The saltwater chlorinator needs a sufficient flow of water for effective operation. A dirty skimmer basket, clogged or dirty filter, and a clogged pump strainer, can cause insufficient water flow for the chlorinator to produce less chlorine.
What is salt cell reversing?
As the electricity used in Salt Chlorine Generation is DC (Direct Current), scale will build up on the cell blades. The power supply will reverse the flow of electricity after a programmed amount of time to dissolve the scale off of the blades.
How do you remove a Jandy AquaPure salt cell?
Remove the cell from the Jandy AquaPure Purification System. Remove the sensor from its port on the cell if scaling is detected. Wash the cell well with water. Turn the flow/temp/salinity sensor counterclockwise to remove it from the three-port cell.
How do I test my salt cell?
Submerge the salt cell in a bucket of pool water, but do not get the wiring connections wet. Turn on the pump and activate the salt system. Put the output on the salt system at 100% for this test. Put the output back to the original setting when you are done.
What is the low voltage code on Jandy aquapure?
Front board power supply either too low or too high. (Generates 173 – Low input voltage code if Level 2 code 188 is present) (Generates 170 code if 188 is not present) Contact a pool professional. VAC input voltage is too low.
What should I do if my Jandy pool sensor is not working?
Contact a pool professional Verify proper flow/temperature/salinity sensor installation. Check salinity with Myron “L” meter calibrated for NaCl or test strips. Add salt as necessary Jandy recommends that you contact a pool professional for service if you encounter a Level 2 code. Heated sensor element not heating. (Generates 172 code)
Which is error code is your Jandy unit displaying?
So, which error code is your Jandy unit displaying? Level 1 service codes are more common than level 2 codes and can typically be troubleshooted by the homeowner and a Jandy technical representative.
Is the Jandy aquapure chlorine generator bad?
This happens to a lot of pool owners who may own the Jandy AquaPure Chlorine Generator. It’s not a testimonial of how bad the unit is, ( Jandy is a great manufacturer), but rather how negligent, here I include myself, we can be with product manuals and documents.
