What is HM 10 Bluetooth module?

What is HM 10 Bluetooth module?

HM-10 BLE Bluetooth 4.0 CC2541 Wireless Module is a BLE module for an embedded system to get BLE wireless communication with BLE capable devices (e.g. Android, iPhone, and iPad).

How do you use the HM 10 Bluetooth module?

BLE Scanner Android App

  1. Once the installation is completed, open the App and enable Location and Bluetooth permission.
  2. Scan for the bluetooth devices. The name of HM-10 BLE 4.0 is MLT-BT05. The default pairing code for MLT-BT05 is 123456789. So once connected, you are ready to go now.

How do I change the baud rate of HM 10?

  1. There are 2 versions of the HM-10; the HM-10C and the HM-10S.
  2. Tapping one of the labels will read the characteristic value. For example, under Device Name, tapping the.
  3. At the bottom of the serial monitor, set the baud rate to 9600 and using the above sketch means we can have line end characters selected:

How do I connect two Arduinos via Bluetooth?

Pairing and Binding

  1. set the same baud rate on both devices.
  2. make sure the passwords on the HC-05 and the HC-06 are the same.
  3. find the address of the HC-06.
  4. pair the HC-05 with the HC-06.
  5. bind the HC-06 to the HC-05.
  6. set the HC-05 to only connect with paired devices.
  7. link to the HC-06.

How do I upgrade HM-10?

Steps to Update Firmware in HM10 Bluetooth Module using Arduino Uno

  1. Firstly, download and Upload the CCloader Sketch on Arduino Uno Using the Arduino IDE.
  2. Now wire the HM-10/CC2541 Board to the Arduino according to below table after soldering the wires on HM-10 board:

How do I use a Bluetooth module with Arduino?

How to use the App?

  1. Download the Application form here or here.
  2. Pair your device with HC 05/06 Bluetooth module1) Turn ON HC 05/06 Bluetooth module2) Scan for available device3) Pair to HC 05/06 by entering default password 1234 OR 0000.
  3. Install LED application on your android device.
  4. Open the Application.

What is the difference between HC 05 and HC 06?

The HC-05 can be a master or slave. The HC-06 is a slave only. This means the HC-05 can initiate a connection to another device and the HC-06 can only accept a connection from another device.

How do you program a HM 10 module?

Just connect as following:

  1. Connect 3.3V of Arduino to the VCC of HM-10.
  2. Connect GND of Arduino to the GND of HM-10.
  3. Connect D8 of Arduino to RX of HM-10.
  4. Connect D7 of Arduino to TX of HM-10.
  5. Connect D2 of Arduino to the long leg of LED along with a 220 ohm resistor.
  6. Connect the short leg of LED with the GND of Arduino.

How do I upgrade HM 10?

How do I know if my Bluetooth module is working?

Testing HC-05 bluetooth module using Arduino UNO as serial to USB converter

  1. First make sure your HC-05 Bluetooth Module is paired with your mobile.
  2. Click on “SELECT DEVICE” icon to select paired Bluetooth module.
  3. When you press “UP Arrow” it sends the data “A” to Bluetooth Module connected with the circuit.

What is master Bluetooth module?

Reference: HCMODU0061. This class 2 Bluetooth module (HC-05) comes programmed with firmware that allows it to pass the output of a serial communications port (default is 9600 baud) over a Bluetooth wireless connection with no software configuration….

How do I connect HM 10 to Arduino?

Is the HM-10 a Bluetooth 4.0 module?

The module. The HM-10 is a readily available Bluetooth 4.0 module based on the Texas Instruments CC2540 or CC2541 Bluetooth low energy (BLE) System on Chip (SoC). The module design and firmware originated from the Jinan Huamao Technology Company (JNHuaMao), but is sold by various suppliers. For the class, we got the HM-10 shipped on…

What is the pairing code for HM-10 ble 4.0?

Scan for the bluetooth devices. The name of HM-10 BLE 4.0 is MLT-BT05. The default pairing code for MLT-BT05 is 123456789. So once connected, you are ready to go now. Now once the connection with MLT-BT05 is done, click on it and you will get many options like Device Information, Generic Access, Generic Attribute, Custom Service.

What kind of Bluetooth module does jnhuamao use?

The module Fig. 1: HM-10 Bluetooth module from JNHuaMao, based on the CC2540 TI chip. The HM-10 is a readily available Bluetooth 4.0 module based on the Texas Instruments CC2540 or CC2541 Bluetooth low energy (BLE) System on Chip (SoC).

Which is better HM-10 module or BLE chip?

The module is preferred where power consumption is issue. HM-10 MODULE is designed by BLE chip so it consumes very less power to function. So the module can be used on mobile systems. The module is cheap so it can be installed in low cost systems.

Back To Top