How do I program my scanner 94 pro?
Re: need to know how to program a radio shack pro-94… Press the “prog” key followed by the “Trunk” key then the number “1” key. Press the “E” key. you must press the E key and the Prog key after each frequency, after you finish entering your frequencies, press the scan key.
How do you use the Radio Shack dual trunking scanner?
Turn on the scanner by turning the volume knob clockwise. The screen will display the message, “Welcome to Dual Trunking.” Turn the “Squelch” knob clockwise until the indicator is pointed to “Min.” Slowly turn the dial counterclockwise until there is no background noise.
How do you unlock channels on Radio Shack scanner?
Press L/OUT to unlock a channel. If there are no locked out channels, then the scanner will just beep. Note: You can still monitor locked out channels in manual and program modes.
How do you reset a Radio Shack police scanner?
From the owner’s manual, Power on the scanner, and while the “Welcome” screen is showing, press the “zero” key followed by the “one” key.
How do I program my trunking scanner?
Enter programming mode on your scanner by pressing “Prgm” on the control panel. Press the “Trunk” button to select the trunked frequency option and then enter in the trunk number you want to program. This will be a number between 1 and 10. Locate a list of available trunk types and frequencies.
How do you program a Radio Shack police scanner?
Press the “Program” button, then “Limit.” “LO” will appear on the screen. Enter the low frequency where you want to begin searching. Press the “WX/E” button and “HI” will appear on the screen. Enter the highest frequency you want to search to and press “WX/E” again.
How do you program a realistic Pro 2028 scanner?
Press the “Program” key and then press “Limit.” Enter the lowest frequencies you want to scan. Press “Program” and “Limit” and enter the highest frequencies you want to scan. Press “Enter” to scan frequencies. Press “Monitor” to store the frequency or the up or down arrows to continue scanning.
What does lockout mean on a scanner?
Temporary Lock-Out Function – lets you set your scanner to skip over specified channels or frequencies when scanning or searching. This temporary lock-out releases when you manually unlock the channels or frequencies or when you power down the scanner.
How do I reset my RadioShack 95 scanner?
To Reset the scanner, turn off the scanner then turn it back on. Insert a pointed object, such as a straightened paper clip, into the reset opening above and to the right of the power jack on the side of the scanner. Then gently press and release the reset button inside the opening.
How do I reset my handheld scanner?
Force a software reset (Reset factory defaults).
- Press and hold the scan button. Continue to hold the scan button for approximately 20 seconds until the scanner beeps twice and vibrates.
- Release the scan button then press it rapidly five times while the RED LED is on.
What does trunking mean on a scanner?
A trunked radio system is a two-way radio system that uses a control channel to automatically assign frequency channels to groups of user radios. These systems typically have access to multiple channels, up to 40-60, so multiple groups in the same area can communicate simultaneously.
How can I use Win95 on my pro-95?
Using Win95, program an out-of-range frequency into some channel. On the PRO-95, select that channel in “manual mode”. Press FUNC TUNE. The scanner will no search up (or down) from that frequency. If you let it enter a “valid” range, it won’t go back to the invalid range, so you’ll have to select the channel and hit FUNC TUNE again.
What is Win95 for Radio Shack pro-95 trunking scanner?
Programming Cable Information Win95 is a Windows “GUI” application for the Radio Shack Pro-95 trunking scanner. It allows you to read data from the scanner, make changes via the GUI, and write the modified data back. It will read / write the scanner in approximately 80 seconds.
How do I upload a P95 file to a scanner?
You download from the scanner, select Open from the File menu to load an existing P95, P93 or text file, or select New from the File menu to start from scratch. You then set up your frequencies, trunking information, and other scanner settings. Next, upload to the scanner and save the file.
