What is the interface range command?

What is the interface range command?

The interface range command allows you to configure multiple interfaces at once. The interface range command is particularly useful because switches have many interfaces and the same settings are often applied to multiple interfaces.

How do I set the interface range in Juniper?

To specify a member range, use the member-range statement at the [edit interfaces interface-range name ] hierarchy level. To specify interfaces in lexical order, use the member-range start-range to end-range statement.

What is interface f01?

on a cisco switch ethernet interface fa 0/1 mean. fa means fast ethernet.

How do I configure multiple Cisco switch ports at the same time?

Configuring Multiple Switch Ports on the Same VLAN

  1. In Dashboard, navigate to Switch > Configure > Switch Ports.
  2. Check the boxes next to each port to be updated.
  3. Click Edit, specify the VLAN, and click Update.

How is VLAN configured?

To configure VLANs, follow these guidelines:

  1. Create the VLANs.
  2. (Optional) Set the desired VLAN-related configuration for ports.
  3. Assign interfaces to VLANs.
  4. (Optional) Configure VLAN groups on your switch.
  5. (Optional) Configure TV VLAN settings on your switch.

What is EtherChannel networking?

EtherChannel is a port link aggregation technology or port-channel architecture used primarily on Cisco switches. It allows grouping of several physical Ethernet links to create one logical Ethernet link for the purpose of providing fault-tolerance and high-speed links between switches, routers and servers.

How do I disable Juniper interface?

– To Juniper disable interface:

  1. root@Juniper# set interfaces ge-0/0/1.0 disable << This is cisco equivalent of “shutdown” – To Juniper enable interface:
  2. root@Juniper# delete interfaces ge-0/0/1.0 disable << This is cisco equivalent of “no shutdown” Verification:
  3. root@Juniper#show ge-0/0/1.0.

What is the use of the interface Els?

The ELS platform is the interface between your application and the ELS services. It provides a simple way to implement several kinds of linguistic functionality through the same API, which allows the application to access and use specific services.

What is an interface switch?

With a switch interface, the user can plug the switch into the switch interface and then plug the switch interface into one of the computer ports such as a USB port. Switch interfaces often allow for multiple switches to be plugged in at once.

What does it mean when an interface is administratively down?

When an interface shows administratively down it means that if you look at the configuration you will see a line that says “shut”. Just go into config t and the interface and do a “no shut” this should bring the interface administratively up.

What is the command used to assign all user ports to VLAN 99?

Issue the show vlan brief command to verify that all ports are in VLAN 99.

How do I configure a switch port?

To configure the switch so that you can connect an appropriate device to a port and have it work, follow these steps: Connect to your switch and get into Configuration mode using a set of commands like the following: Switch1>enable Password: Switch1#configure terminal Enter configuration commands, one per line.

When do you use the interface range command?

Interface range command. If you have multiple interfaces that need to be configured with the same settings, you can use the interface range command to specify a range of interfaces to which the subsequent commands will be applied.

How is interface range configured in Cisco router?

Note – in the above configuration, multiple interfaces (Fa2/1 – 4 and Gi1/1 – 3) of Cisco Router have been assigned speed and duplex settings through a single “ Interface Range ” command. Also, if the interfaces are discontinuous, still they can be mapped in the same command by using a Comma (,).

Can you use F0 / 1-24 in FastEthernet?

02-16-2009 09:19 PM The command f0/1 – 24 will work, as will fa0/1 – 24, as will fastEthernet0/1 – 24. The IOS knows that you are abbreviating FastEthernet by using f or fa (or anything that spells the word out) so it will work, since there are no other interface types that start with f (at least on most switches anyway).

How to configure Zee FastEthernet 0 / 1, Fast Ethernet 0 / 2?

1)Do we need to configure the ” interface range fastethernet 0/1, fast ethernet 0/2″ first before we can use the command”defineinterface-range zee fastethernet 0/1, fastethernet 0/2″ ? 2) switch puts ports in errdisable for different errors.

Back To Top